OUR STORES

blog-placeholder

XStore London

Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud. Lorem ipsum dolor sit amet, consectetur adipiscing. Ut enim ad minim veniam, quis nostrud. Lorem ipsum dolor.

Store Address

48 Park Avenue, East 21st Street, Apt. 304
London NY 10016

Contact Info

Email: youremail@site.com
Phone: +1 408 996 1010
Fax: +1 408 996 1010

This post is also available in: Italiano (Italian) Русский (Russian) 简体中文 (Chinese (Simplified))

MONOCHROMATIC EFFECTS:

SBRECCIATO

Apply diagonally a coating of uniform thickness of CeboArt Model tinted into the desired colour using the toothed edge of the stainless steel Shark trowel (A/55); then make a second passage using the smooth edges of the same trowel until you get an alternate sequence of smooth and diagonal bands of different dimensions. While the product is still wet, dab the surface or scratch it irregularly with the CeboSign tool (A/35) following the direction of the strokes. Before the product gets completely dry, smooth it out with a stainless steel trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water.

ONDA

Apply vertically or horizontally a coating of uniform thickness of CeboArt Model tinted into the desired colour using the toothed edge of the stainless steel Shark trowel (A/55); then smooth the product out using the smooth edges of the same trowel. While the product is still wet, work the surface with the PVC trowel “Onda 4” following the chosen vertical or horizontal direction. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

SPATOLATO

Using a steel trowel apply a coating of uniform thickness of CeboArt Model tinted into the desired colour, then create the required esthetic effect working the surface with the trowel, making criss cross irregular strokes. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.


CeboWax

CeboWax, tinted and diluted with max 30% of water, is applied onto completely dry CeboArt Model. It should be applied in one or two coatings with a synthetic sponge from the bottom upwards.

CeboFlow

CeboFlow is a ready-to-use product, it should be applied with a brush in one coating until the surface is completely saturated. Proceed from the bottom upwards to avoid sagging.

MATT GLAZING DECORATIONS:

CRAQUELÉ

Using a roller apply a coating of CeboFix R tinted into the desired colour that will determine the cracks colour. When CeboFix R is completely dry, apply a coating of CeboBreak working in criss cross strokes until the surface is completely saturated. When the surface is dry, it should be translucid. After minimum 4 hours and maximum 24 hours, using a steel trowel apply a coating of uniform thickness of white CeboArt Model, then create the required esthetic effect working the surface with the trowel, making criss cross irregular strokes. Wait for the cracks to form. Before the product gets completely dry, smooth it out, slightly flattening the salient patches.

Effetto DESIGN Rilievo – DESIGN Relief effect

Apply the first coating of white CeboArt Model levelling and smoothing the surface with a stainless steel trowel; when the surface is dry, attach the stencil to the wall with some masking tape and apply a second coating of CeboArt Model, making strokes from the edges of the stencil to its centre and making sure to keep its rear side clean. Afterwards, attach another stencil and continue as described before, repeating the operation as many times as necessary. It is advisable to remove the stencils while the product is still wet, while any resulting defect may be removed when the surface is dry.

TIVOLI

Using a steel trowel apply a coating of uniform 1-2 mm thickness of white CeboArt Model. While the product is still wet, work the surface with the special CeboSign tool (A/35) to create the veins typical for stone. In order to obtain a more natural effect proceed irregularly and avoid repeating the same pattern. Using a punch make incisions on the surface to create the effect of stone blocks. Before the product gets completely dry, smooth it out with a trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water.


CeboWax

CeboWax, tinted and diluted with max 30% of water, is applied onto completely dry CeboArt Model. It should be applied in one or two coatings with a synthetic sponge from the bottom upwards.

METALLIC EFFECTS:

CREATIVA

Using a steel trowel apply a thick coating of uniform thickness of white CeboArt Model. While the product is still wet, work the surface with the special Sahara tool (A/64) to create the chosen pattern. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

DRAFT

Using a stainless steel trowel apply a non-uniform coating of white CeboArt Model varying the application direction; while the product is still wet, make irregular incisions on the surface using the special CeboSign tool (A/35). Before the product gets completely dry, smooth the surface out with a trowel, flattening slightly the salient patches; if the product is too dry, you can wet it with sprayed water.

ONDA

Apply vertically or horizontally a coating of uniform thickness of white CeboArt Model using the toothed edge of the stainless steel Shark trowel (A/55); then smooth the product out using the smooth edges of the same trowel. While the product is still wet, work the surface with the PVC trowel “Onda 4” (A/56) following the chosen vertical or horizontal direction. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

ZEFFIRO

Apply a coating of uniform thickness of white CeboArt Model using the toothed edge of the Shark trowel (A/55) and making horizontal or vertical strokes: make sure to smooth it subsequently using the smooth edge of the Shark trowel. It is recommended to apply and then work the product in bands about 1 metre wide. Using the special CeboSign tool (A/35) scratch the surface in the chosen direction (horizontal or vertical); before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

SBRECCIATO

Apply diagonally a coating of uniform thickness of white CeboArt Model using the toothed edge of the stainless steel Shark trowel (A/55); then make a second passage using the smooth edges of the same trowel until you get an alternate sequence of smooth and diagonal bands of different dimensions. While the product is still wet, dab the surface or scratch it irregularly with the CeboSign tool (A/35) following the direction of the strokes. Before the product gets completely dry, smooth it out with a stainless steel trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water.

COCCODRILLO

Apply vertically or horizontally a coating of uniform thickness of white CeboArt Model using the toothed edge of the stainless steel Shark trowel (A/55); then smooth the product out using the smooth edges of the same trowel. While the product is still wet, work the surface with the special roller “Coccodrillo” (A/61-A/62) following the chosen vertical or horizontal direction. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

Effetto DESIGN Rilievo – DESIGN Relief effect

Apply the first coating of white CeboArt Model levelling and smoothing the surface with a stainless steel trowel; when the surface is dry, attach the stencil to the wall with some masking tape and apply a second coating of CeboArt Model, making strokes from the edges of the stencil to its centre and making sure to keep its rear side clean. Afterwards, attach another stencil and continue as described before, repeating the operation as many times as necessary. It is advisable to remove the stencils while the product is still wet, while any resulting defect may be removed when the surface is dry.


CeboStyle Antico

When CeboArt Model is completely dry, apply the first colour of CeboStyle Antico using the CeboSi brush 4” (A/27), following the pattern direction, then immediately shade the surface with a synthetic sponge. Using a synthetic sponge apply the second colour of CeboStyle Antico (it is possible to dilute it with 20% of water) on the previously created veins in order to make them clearer and brighter; the rest of the surface should keep the colour of the first coating.

NEOCLASSICAL EFFECTS:

Effetto DESIGN Liscio – DESIGN Smooth effect

Apply the first coating of CeboArt Model tinted in the desired colour, levelling and smoothing the surface with a stainless steel trowel; when the surface is dry, attach the stencil to the wall with some masking tape and apply a coating of tinted CeboArt Lux (diluted with 10-15% of water) with a small roller, making sure to keep the rear side clean. Afterwards, move the stencil laterally, following the pattern, and continue as described before, repeating the operation as many times as necessary. Any resulting defect may be smoothed with a stailess steel trowel while the product is still wet or polished with sandpaper when the surface is dry.


Note: the products used to create the effect described above should be tinted in various shades of the same colour, following this scheme: T for the background coating of CeboArt Model, F for CeboArt Lux applied with a stencil, T for the finish coating of CeboArt Lux.

DESIGNER WALLS:

Effetto DESIGN Retrò – DESIGN Retrò effect

Apply the first coating of white CeboArt Model levelling and smoothing the surface with a stainless steel trowel; when the surface is dry, attach the stencil to the wall with some masking tape and apply a second coating of CeboArt Model, making strokes from the edges of the stencil to its centre and making sure to keep its rear side clean. Proceed creating an alternate and irregular pattern, leaving empty areas that will be subsequently filled with the second coating of white CeboArt Model. Before the product gets completely dry, smooth it out with a stainless steel trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water.

CREATIVA

see description in the previous chapters.

SBRECCIATO

see description in the previous chapters.

NIAGARA

Apply CeboArt Model tinted in the chosen colours + white with vertical strokes, making sure to alternate various colours creating the desired pattern. It is reccommended to use the quantity of material necessary to create the pattern; before the product gets completely dry, smooth it out keeping the colours separate as much as possible. When you get to final polishing, if the product is too dry, you can wet it with sprayed water.

CATALOGUE

The shades here presented are computer colour simulations; they must therefore be considered as indicative only, and not binding. Please refer to the Colour Cards with original samples, available with our authorised Dealers.