Preparation of supports
Check that the supports are uniform, perfectly clean and dry. In the presence of recent shavings, chalky or absorbent surfaces, clean the surface thoroughly and first apply the CeboFix M insulating fixative in one hand, with a brush, diluted 1:1 with water.
CeboIdea is a water-based acrylic microcoating for interiors, smooth and compact, which allows the creation of effects that give the walls a high depth and three-dimensional design.
Application of CeboIdea: CeboIdea, colored in the same shade as CeboModern or in the colors indicated on the chart, can be applied with a stainless steel trowel (A/39-A/40) or with a polygonal or rectangular polycarbonate trowel (A/19-A/20) and , before complete drying, it can be slightly smoothed with the Caress Spatula (A/38). CeboIdea can be easily sanded, once dry, to eliminate any imperfections and to refine the various effects before the subsequent application of CeboModern.
Application of CeboIdea
Millerighe effect: apply CeboIdea, colored in the same shade as CeboModern, with the trowel chosen as indicated above, in a uniform thickness of 1-2 mm, in vertical bands of 1 m. approximately and, while the product is still damp, go over the treated surface again with the Trowel or with the oval plastic pad (A/41) in the same direction, and carry out a light smoothing with the Caress Spatula: once the CeboIdea has dried (6-8 hours ) sand to eliminate any imperfections.
Nuvola effect: apply CeboIdea, colored in the same shade as CeboModern, with the polycarbonate trowel, in a uniform thickness of 1-2 mm: after 2-3 m2, while the product is still wet, go over the treated surface again, with circular and uniform movements , with the same trowel or with an oval plastic pad (A/41) and smooth with the Caress Spatula. Wait for CeboIdea to dry completely (6-8 hours) and sand to eliminate any imperfections.
Spatolato effect: apply CeboIdea, colored in the same shade as CeboModern, with the trowel chosen as indicated above, in a uniform thickness of 1-2 mm; after 2-3 m2, while the product is still wet, create the aesthetic effect by working with the Trowel with irregular spatula strokes and smooth gently with the Caress Spatula. Wait for CeboIdea to dry completely (6-8 hours) and sand to eliminate any imperfections.
Disco effect: apply CeboIdea, colored in the same shade as CeboModern, with the trowel chosen as indicated above, in a uniform thickness of 1-2 mm; after 1-2 m2, while the product is still wet, create the aesthetic effect with a 12 cm notched trowel, making semicircular movements. Wait for CeboIdea to dry completely (6-8 hours) and sand to eliminate any imperfections.
Three-dimensional effects with CeboDesign: on a smooth surface, prepared with FondoPlus or smoothed with CeboIdea, plumb and fix the stencil (CeboDesign) to the wall with adhesive paper tape: apply CeboIdea, colored in the same shade as CeboModern, with the Trowel in polycarbonate (A19-A/20) in a thickness of 1-2 mm, taking care to cover the stencil evenly starting from the sides towards the center and being careful not to dirty the back of the stencil. Then place a second stencil next to it and proceed as above, repeating the operation as many times as necessary. It is recommended to remove the stencil while the product is still wet: any imperfections can be sanded when the surface is dry.
CeboModern: single-component polyacrylic finish with metal effect pigments.
Application of CeboModern: on dry and dust-free CeboIdea, respecting the direction of processing, apply the first coat of CeboModern with the Cebos Plafoncino (A/23-A/24); once the first coat has dried (4 hours), apply the second coat in the same way. After 4/6 hours, apply the third hand and delicately blend the surface using a synthetic sponge.