• a03715b1-be76-4d35-a7ca-f21151b95d5a.png

    CeboMarmo, PIETRA CLASSICA

    delicate spatula strokes give depth and shine to the surfaces

    CeboMarmo

CeboMarmo, PIETRA CLASSICA

High-quality water-based acrylic finish for interiors, with a glossy appearance. CeboMarmo reinterprets the marble effect by reproducing the movements of the typical veins and the brilliance of a precious and refined material, giving an exclusive charm to every environment.

The surfaces must be perfectly smooth and flat: otherwise defects in the support could be highlighted during the application of CeboMarmo and especially during the polishing phase. In the presence of smoothing, chalky or absorbent primers, apply a coat of CeboFix M fixative with a brush, diluted 1:1 with water.

Application of CeboFix Primo: apply the white CeboFix Primo primer in one hand, with a short-haired roller, diluted 20% with water and wait for it to dry completely (minimum 6-8 hours).

Application of CeboIdea: to obtain a smooth surface, without imperfections, roll or brush marks and to have an ideal adhesion base, on CeboFix Primo dry it is recommended to apply, with a stainless steel trowel, one or two coats in succession of the base CeboIdea and sand gently with 180 grit sandpaper: dust the surface with a damp cloth. Then start applying CeboMarmo directly on CeboIdea.

FIRST PHASE
Apply the first coat of CeboMarmo colored with stainless steel Frattone, with crossed and regular spatulates, in order to obtain a smooth and uniform surface. Wait for complete drying (6-8 h).

SECOND PHASE
Remove any imperfections and, if necessary, sand by hand or machine with abrasive grain 180. Apply the second coat of CeboMarmo following the same methods used for the first coat. After about 4 h, apply the third coat of CeboMarmo, to spatulate crossed over the entire surface. Use the steel spreader again, exerting adequate pressure, to compact the product.

POLISHING
OPTION 1 - Polishing by hand - before complete drying, using the perfectly clean stainless steel trowel, polish the surface.
OPTION 2 - Machine polishing - After minimum 2-4 h from the application of the last coat of CeboMarmo, carry out polishing by sequentially using the abrasive discs: 1     
PLEASE NOTE: After machine polishing, a hand polishing with a steel trowel is required.

PROTECTION AND FINAL POLISHING
CeboWax: a breathable, water-repellent, beeswax-based interior finish. Apply a coat of 1:1 diluted CeboWax with water, using a synthetic sponge. Spread the product for about 1 square meters at a time following the direction of processing: immediately after, with a soft cloth, review the surface to remove excess wax. Wait 10-15 minutes and polish the surface repeatedly passing the perfectly clean steel trowel or polish with 4000 grit abrasive disc.


  • product use dilution (water) approx.coverage tool drying time colour
    white base coat CeboFix Primo interior 20% 10 m2/L 6-8 h white
    preparation base coat CeboIdea interni ready to use 2-3 m2/L 6-8 h CeboKit and CeboCol
    finish coat CeboMarmo interni ready to use 4-5 m2/L 6-8 h CeboKit & CeboCol
    finish coat CeboWax interior 1:1 16 m2/L 4-6 h transparent

  • If more than one pack has to be produced in the same color, it is advisable to use bases and colorants carrying the same batch number.

    CEBOMARMO CEBOKIT: /05 /1 /2 /4 8 /M 301-307
    12 L 25 ml 50 ml 100 ml 200 ml 400 ml 300 ml
    4,8 L 10 ml 20 ml 40 ml 80 ml 160 ml 120 ml
    1,2 L 2,5 ml 5 ml 10 ml 20 ml 40 ml 30 ml