• 086bfbf9-cf6d-4370-8351-a5c35473c0ad.png

    CeboMarmo, PIETRA NOBILE one-tone

    strong lines and nuances intense make up elegant games light-dark

    CeboMarmo

CeboMarmo, PIETRA NOBILE one-tone

High-quality water-based acrylic finish for interiors, with a glossy appearance. CeboMarmo reinterprets the marble effect by reproducing the movements of the typical veins and the brilliance of a precious and refined material, giving an exclusive charm to every environment.

The surfaces must be perfectly smooth and flat: otherwise defects in the support could be highlighted during the application of CeboMarmo and especially during the polishing phase. In the presence of smoothing, chalky or absorbent primers, apply a coat of CeboFix M fixative with a brush, diluted 1:1 with water.

Application of CeboFix Primo: apply the white CeboFix Primo primer in one hand, with a short-haired roller, diluted 20% with water and wait for it to dry completely (minimum 6-8 hours).

Application of CeboIdea: to obtain a smooth surface, without imperfections, roll or brush marks and to have an ideal adhesion base, on CeboFix Primo dry it is recommended to apply, with a stainless steel trowel, one or two coats in succession of the base CeboIdea and sand gently with 180 grit sandpaper: dust the surface with a damp cloth. Then start applying CeboMarmo directly on CeboIdea.

FIRST PHASE
Apply CeboMarmo in the chosen color with stainless steel Frattone, diagonally or vertically over the entire surface. Wait for complete drying (minimum 6-8 h).

SECOND PHASE
Remove any imperfections and, if necessary, sand by hand or machine with abrasive grain 180. Apply the second coat of CeboMarmo in the same color with the steel trowel over the entire surface, respecting the sense of the first coat. Refit with the steel spreader applying adequate pressure to uniform and compact the product.

POLISHING
OPTION 1 - Polishing by hand - before complete drying, using the perfectly clean steel trowel, polish the surface, exerting adequate pressure.
OPTION 2 - Machine polishing - After minimum 2-4 h from the application of the last coat of CeboMarmo, carry out polishing by sequentially using the abrasive discs: 1    
PLEASE NOTE: After machine polishing, a hand polishing with a steel trowel is required.

PROTECTION AND FINAL POLISHING
CeboWax: a breathable, water-repellent, beeswax-based interior finish. Apply a coat of 1:1 diluted CeboWax with water, using a synthetic sponge. Spread the product for about 1 square meters at a time following the direction of processing: immediately after, with a soft cloth, review the surface to remove excess wax. Wait 10-15 minutes and polish the surface by repeatedly passing the perfectly clean steel trowel or polish with 4000.P grit abrasive disc.

  • product use dilution (water) approx.coverage tool drying time colour
    white base coat CeboFix Primo interior 20% 10 m2/L 6-8 h white
    preparation base coat CeboIdea interni ready to use 2-3 m2/L 6-8 h CeboKit and CeboCol
    finish coat CeboMarmo interni ready to use 4-5 m2/L 6-8 h CeboKit & CeboCol
    finish coat CeboWax interior 1:1 16 m2/L 4-6 h transparent

  • If more than one pack has to be produced in the same color, it is advisable to use bases and colorants carrying the same batch number.

    CEBOMARMO CEBOKIT: /05 /1 /2 /4 /8 /M 301-307
    12 L 25 ml 50 ml 100 ml 200 ml 400 ml 300 ml
    4,8 L 10 ml 20 ml 40 ml 80 ml 160 ml 120 ml
    1,2 L 2,5 ml 5 ml 10 ml 20 ml 40 ml 30 ml