High-quality water-based acrylic finish for interiors, with a glossy appearance. CeboMarmo reinterprets the marble effect by reproducing the movements of the typical veins and the brilliance of a precious and refined material, giving an exclusive charm to every environment.
The surfaces must be perfectly smooth and flat: otherwise defects in the support could be highlighted during the application of CeboMarmo and especially during the polishing phase. In the presence of smoothing, chalky or absorbent primers, apply a coat of CeboFix M fixative with a brush, diluted 1:1 with water.
Application of CeboFix Primo: apply the white CeboFix Primo primer in one hand, with a short-haired roller, diluted 20% with water and wait for it to dry completely (minimum 6-8 hours).
Application of CeboIdea: to obtain a smooth surface, without imperfections, roll or brush marks and to have an ideal adhesion base, on CeboFix Primo dry it is recommended to apply, with a stainless steel trowel, one or two coats in succession of the base CeboIdea and sand gently with 180 grit sandpaper: dust the surface with a damp cloth. Then start applying CeboMarmo directly on CeboIdea.
FIRST PHASE
Apply CeboMarmo white with stainless steel Frattone, diagonally. To avoid that the product can dry before the overlapping of the other colors, it is recommended to proceed with the laying for about 2 square meters at a time. On the product still fresh, apply the other colors of CeboMarmo, one at a time, always respecting the sense of processing. Repeat over the entire surface. Wait for complete drying (minimum 6-8 h).
SECOND PHASE
Remove any imperfections and, if necessary, sand by hand or machine with abrasive grain 180. With a watercolor pencil draw the veins and blend them with a brush from fine arts moistened with water. Once the decorative part is finished, apply CeboMarmo white with the steel trowel over the entire surface, respecting the sense of workmanship. Review by exerting adequate pressure to compact and standardize the product.
POLISHING
OPTION 1 - Hand polishing - before complete drying polish the surface by repeatedly passing the clean steel trowel, exerting adequate pressure.
OPTION 2 - Machine polishing - After minimum 2-4 h from the application of the last coat of CeboMarmo, carry out polishing by sequentially using the abrasive discs: 1
PLEASE NOTE: After machine polishing, a hand polishing with the steel trowel is required.
PROTECTION AND FINAL POLISHING
CeboWax: a breathable, water-repellent, beeswax-based interior finish. Apply a coat of 1:1 diluted CeboWax with water, using a synthetic sponge. Spread the product for about 1 square meters at a time following the direction of processing: immediately after, with a soft cloth, review the surface to remove excess wax. Wait 10-15 minutes and polish the surface repeatedly passing the perfectly clean steel trowel or polish with 4000 grit abrasive disc.
product | use | dilution (water) | approx.coverage | tool | drying time | colour | |
---|---|---|---|---|---|---|---|
white base coat | CeboFix Primo | interior | 20% | 10 m2/L |
![]() ![]() |
6-8 h | white |
preparation base coat | CeboIdea | interni | ready to use | 2-3 m2/L |
![]() |
6-8 h | CeboKit and CeboCol |
finish coat | CeboMarmo | interni | ready to use | 4-5 m2/L |
![]() |
6-8 h | CeboKit & CeboCol |
finish coat | CeboWax | interior | 1:1 | 16 m2/L |
![]() ![]() |
4-6 h | transparent |
CEBOMARMO | CEBOKIT: /05 | /1 | /2 | /4 | /8 | /M 301-307 |
---|---|---|---|---|---|---|
12 L | 25 ml | 50 ml | 100 ml | 200 ml | 400 ml | 300 ml |
4,8 L | 10 ml | 20 ml | 40 ml | 80 ml | 160 ml | 120 ml |
1,2 L | 2,5 ml | 5 ml | 10 ml | 20 ml | 40 ml | 30 ml |